Sie greifen anscheinend aus Europa zu.
Möchten Sie bei webike.eu.com?
- Auf Lager
68.5 EUR (12,858 JPY)
Webike Punkte: +386 pt
(2.05 EUR)
Lieferinformationen
Auf Lager : 3 übrig, Versand innerhalb 24 Stunden.
Voraussichtliches Ankunftsdatum ca.
Produktbeschreibung unten wird automatisch übersetzen durch Google.
Einzelheiten zum Produkt
[Product Contents]
・PumpShaft
・Oil sealAdapter
・AluminumImpeller(19215-GC4-731)
・Copper Washer(90447-KE1-000)
Oil seal for pump(91211-KA3-761)
・Bearing (96100-60010-00)
Oil seal DMROriginal fluorine (91201-035-015)
() is HondaOEM Parts No..
**Please be sure to work with the hydraulic press all the press-fitting work. The hammer tapping is strict prohibition!
*It contains other products in the photo.
*Please note that the product specification may change due to manufacturer reasons.
.
These are DMR-JAPAN original parts..
High spec from Street to Circuit, it improves acceleration, response, and fuel economy..
[Lightweight & Rigid]
PumpShaft is made of 64Titanium, which is lightweight, hard, and corrosion resistant..
The rust around the pump is necked for the Circuit, which uses fresh water, but the TitaniumShaft is a material that is extremely resistant to rusting..
[Low Friction]
By changing from a large mechanical seal with friction resistance to a small oil seal with friction resistance, the rotational energy lost by the water pump can be transferred to the rear wheels without wasting any energy!
for WPOil seal is HondaRacer's CR/RSetc.. HondaOEM Product" is used for.
[Lightweight Impeller]
Lightweight AluminumImpellerSpec for HondaRacerCR80. Reducing inertia weight with the new pump contributes to less pump-up..
[How to install]
(1) Always press-fit with a hydraulic PRESS.. Do not install the Impeller or use a jig to directly press only the Screw..
(2) Be sure to lubricate both press-fit areas to prevent galling.. Press-fit the engine so that the engine side is flat.. If you make a mistake in the opposite direction, the GEAR will interfere with the Bell RingOuter and prevent it from turning smoothly..
(3)Remove and clean the bearing, oil seal, and mechanical seal before installing a new bearing and oil seal..
(4)Thinly and evenly etc. Liquid Gasket on Oil sealAdapter. Paint on.
(5) Press-fit with hydraulic PRESS.
(6) Wipe off the overflowed Liquid Gasket..
(7)Oil seal should be inserted with the concave side toward the front.. Silicone oil will improve the glide and allow you to insert it deeper..
(8)Apply a small amount of Locktite to the base of the shaft, insert the shaft, and leave it until fully cured (do not apply to the BearingInner).. (Material adhering to the tip of the shaft can get inside the oil seal and cause leakage.).
(9)Apply anti-gnawing Threat Compound to the Screw section.. Don't forget to include Copper Washer!.
(10)Tighten with approx. 1kg-m (Impact wrench strictly prohibited)＼(^_^)/.
Vorsicht
* Wenn eine Bedienungsanleitung enthalten ist, wird diese auf Japanisch verfasst sein.
NEUANKÖmmlinge GEBRAUCHTTEILE FÜR
NEUANKÖmmlinge GEBRAUCHTTEILE FÜR
NEUANKÖmmlinge GEBRAUCHTTEILE FÜR
Neue Ankünfte bei Gebrauchten
Neue Ankünfte bei Gebrauchten
Kundenbewertungen
Es gibt noch keine Kundenbewertung.
Inspiration für den kompletten Custom-Umbau
