MONKEY Ansaugkrümmer Einstellbare Befestigung

If you put "with Cell motorEngine" on MONKEY, you will not be able to install carburetor, so you will need this in high probability.
It depends on the Tank, but I was disappointed that the only angle on my MONKEY was where the Fuel Cock was about to hit Limit.

I bought it to mount the MAGNA50 carburetor backwards
Product name is [MONKEY Intake Manifold Adjustable Attachment] But the HondaHorizontal, including the SUPER CUB I think TypeEngine can be used to install anything

Normal cylinder head with 16mm in take port diameter ring and The ring of 22mm diameter in take port of regular head system is also included
If nothing is attached, the in take port diameter is 26mm with no steps It can be installed
Of course the mounting bolts (Hexagon Cap dish bolts) are included

In my case, I inserted a 22mm ring into the regular head of SPTakegawa It was installed with the
The upper and lower Gasket is also included, so if you just want to swing it around, this Manifold Variable Just purchase the Attachment and you're done

It will be a little forced, but if you prepare a long M6 Bolt, without pivoting, just It may also be used as a Spacer

MAGNA50 has Cell Motor, so Carburetor is installed backwards It's very difficult to do, but thanks to this Manifold Variable Attachment, it's a bit Only the light was visible

I haven't run it yet, but I don't think it's hard to suck secondary air as the cutting accuracy is fine
I didn't know these products were available at this price …
Minimoto is various
Personally, I'd like to have a long hole on the circumference for the plate bolt to attach to the cylinder head It would be nice to be able to fine-tune the angle if I could, but that's asking too much, lol

Overall, the cost performance is good and this is a product that can be called a Recommendation It is

When the engine of MD90 was replaced with the CT110 engine, the carburetor intake was used I bought it to change the face
The gasket is very solid and well designed
The use and performance side of things is still to come

Used for acquaintance's C50 Bore up
Outside for MONKEY IN Manman and PE 28 Carburetor Normal head (High Camshaft)
I had not decided whether to move the carburetor sideways or before, so I'm MONKEY mani so either KITACO swinging 16 pie (Because it is Normal head) I was planning to purchase, but if Minimoto was the way I knew that 16 and 22 could be changed with Attachment. Even if you change the Head you do not have to buy again and there is also the possibility to divert it to another car Horizontal Type.
I am using the KITACO version of 22 for my own CUB but this is useful
We sell maniku more finely from other companies, but the price is also the price and the corresponding carburetor will be limited (If Insec Typecarburetor, can I respond with insurance change?) So KITACO will be able to repurchase mani again and of course you can use it for Horizontal Type other than CUB (Attention per frame as Adapter mani becomes high)
This time Normal head lightly spreading port so I will set it up with 16.
Although it corresponds only to MONKEY, CUB is not machining without pon attachment, is not it also attached other Horizontal Type?
It is JAZZ between Frame and MAGNA It's DAX I do not know solo but from MONKEY is there a narrow Horizontal Type between Engine and Frame?

It is the best adapter!I got it to fit mikuni VM22 carb to 125cm³ chinese engine with starter on top: there was no long 26mm manifold and short one should be rotated because of starter position. Old adapter was with rubber ring which has destroyed and eated by engine after 10000km, I had to change burned-out exhaust valve.Now there is no more airleaks! This adapter is flat and well made, it perfectly adheres to manifold and engine surfaces, new gaskets in kit is very good too.Also used some grey silicone sealant on тоp of mounting bolts to expand the contact surface.Now I can put together my big 26mm carb, 26mm short manifold and 26mm engine intake port for smooth airflow!