Tachowelle

If the cable is attached as it is, the cable and GEAR will not be attached vertically.
You might want to bite the Washer etc.

[How is it used?

The VTR250 that I prepared to start Gymkhana.
Because it was the vehicle which was too cheap and was too battered, I thought to do maintenance before running for the time being, but it became fun to do maintenance custom, and I had to replace Handlebar & rarr;Meter cable and various cables. I had to replace the Handlebar & rarr;Meter cable.

Since the vehicle is not yet assembled, I'm giving it a 3 for now for durability.
I'm hoping to finish it up so I can ride it before 2019 warms up and Corona settles in.


Was the one you received as per Image?

OEM friendly looks.
I could have chosen something with a custom look, but I couldn't resist the ease.


Was the installation difficult?

I also replaced the headlight, so it was a little difficult to pull the cable around the top bridge.
Still, they fit together nicely.

How was your experience with it?

As I mentioned above, I haven't gotten it running yet because it doesn't have the security parts on it.
The original 2 that I started at the same time is finished earlier than the original 2, so even if I finish it, it might become a Gymkhana-only machine.



[Was there anything that disappointed you?

There is not. Even if there was, it is only a story that it is possible to put up with MONSTER S210 book.

I decided to purchased this speedometer cable because of the low price.The build quality almost same as the OEM cable and OEM cable just a little bit pricey than the NTB version.It's been 6years since I first change my bike's(TW200) speedometer cable.So Time Has come to change it.At some times when I was traveling at a speed of more than 80 km/h, I noticed that the needle on the speedometer bouncing back just a little bit.I want to replace the old speedometer cable because I got a brand new speedometer cable from WEBIKE SHOP. Before I remove the old speedometer cable ,First I had to remove the headlight plastic shell and unplug the wiring connector then removed the headlight lamp.SO it was very easy to reach the speedometer cable and unscrew from the speedometer .Then squeeze the speedometer clip/ Remove small clip at bottom of cable housing and free the old speedometer cable from the groove in the brake panel..Before I installed the new speedometer cable ,pull speedo cable out of housing and apply grease (I had tube of waterproof lithium grease handy) to cable as your feeding it back in housing. turn and wiggle it back in all the way.apply a light coat of waterproof grease to the speedometer O-ring ( Brand new speedometer cable doesn't have an O-ring).Install the Brand New speedometer cable into the brake drum and then install the speedometer cable clip into the groove in the brake panel.make sure clip in right by gently trying to pull housing back out.Then need to tighten the upper cable that goes direct to the speedometer itself. 10 minutes Job .After installing the new cable speedo needle has no bounce and steady as a rock on smooth roads.AS ALWAYS THE PACKAGE ARRIVED ON TIME FROM JAPAN AND VERY NICELY PACKED.THANKS FOR THE SUPPORT WEBIKE.Awesome Online Shop.If anyone need parts for your bike Webike Shop is the Best place.Reasonable Prices and 5Star Shop. Cheers !

[How is it used?
Used for HORNET250; Meter needle was shaking, so it was replaced at the same time as OEM Product's Joint.
How was your experience with it?
So far, it has been used without any noticeable drawbacks or problems.
How did it compare to other products?
I think we can say OEM Product same etc.
[Points to note]
When replacing the HORNET meter cable, it is necessary to remove the tank, so some knowledge and tools are required.

[How is it used?
While running, the Speedometer suddenly stayed at Zero, and when the Cable was removed, it was replaced because it was twisted off.
Chose this one because the OEM is discontinued and not sold.

Was the one you received as per Image?
Yes
Was the installation difficult?
No, sir.
However, it is difficult without any work experience at all, such as the need to remove the Meter.
How was your experience with it?
Normal. Perfect.
Very Smooth rotation.

[Included Parts:were they on?
None

[Was there anything that disappointed you?
None
Other items that would be helpful
You can choose to do so with complete peace of mind.
With this Cable, you can ride all the way.