Kabelschutzgitter V3

[How is it used?
of those already using it. Throw away everything but this." The first time I bought the product was when I saw an impression of the product.
It took a lot of courage to invest nearly 5,000 yen in a wire injector, but I was dissatisfied with all the wire injectors I had used so far (*such → https://www.webike.net/sd/2073358/), so I decided to take the plunge and buy one. I was not satisfied with all the wire injectors I have used so far, so I decided to take the plunge and buy one.
In case you are wondering how many times the general wire injector has been replaced (tightening Dial is Quantity:2pc. I have a Set! (and as a result of buying more every time there was a change), so I have 3 or 4, but I don't use them at all.
Classic "Put engine oil in a Vinyl bag and hang it up. This is because you can't hit a Tai KATANA on the method.


Was the one you received as per Image?
As per Image
Translation (Instruction Manual for enter here is included and easy to understand.

How was your experience with it?
Perfection！！！
The oil was perfectly lubricated, with no spurts of oil from the gaps.
What's more! We want to carry out the process of flushing out the dirt inside before lubricating, but until now, the only way to do this was to completely remove the Wire and put it in and out of the kerosene container by hand...etc.
However, with this product, after Parts Cleaner is sprayed, it can be quickly pressed down for cleaning at a great speed.
Gogo gogo gogo gogo gogo gogo gogo gogo gogo gogo gogo gogo gogo!


[Points to note]
The inside rubber packing is oriented.
You will not make a mistake because it is written in the Instruction Manual, but if you lose the Instruction Manual (and you probably will), take a close look at the shape of the Case and Packing to make sure you do not make a mistake.
If you look closely, you can see that the Taper is different!

Also, the Button part to push in is hard at first, so lubricate Large.
If it's not lubricated, it just hurts the belly of the finger that pushes it in.

How did it compare to other products?
The other Cable injector is Garbage.
Replace it now and throw it away.

Points and hangs of ▼ installation/Items to be purchased together/Opinions and requests to the Manufacturer
Other Cable injectors usually have the Body as Material:Aluminum, which is a material with a Body:Plastic, so I'm a little concerned about hydrolysis over time.

[How is it used?
I used to use this type of Cable injector (https://www.webike.net/sd/2073358/), but I wasn't satisfied with it because I didn't feel like I was getting the lube in and it was leaking out.
I heard rave reviews about this product on the Net and wondered if it was true. I thought so I bought it and tried it.

Was the one you received as per Image?
As per Image
Other than that, there is a translation (Instruction Manual of input here is included) that YAZAWA-san may have put in. It is an easy to understand Instruction Manual.

How was your experience with it?
I was able to lubricate it without the lube leaking out due to its shape.
The Stress of lubricating the wires is gone. It is the best.

[Points to note]
There is a direction to the Rubber packing which is shaped like a piece to be put inside.
It is tapered, so you have to frame it so that the taper works.

How did it compare to other products?
The other Cable injector is Garbage. Buy a new one now and throw it away.

Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
I think more people would be happy if it were cheaper.
It's a good buy because things are good.

I bought this one which caught my eye because I didn't like the operation feeling of Wire injector of common Type.

It is the method that the end of the Wire is jointed to the body of the cylinder shape, Grease is injected into the inside, and Grease is pushed in directly with the piston of the upper part. It is overwhelming smallness of the leak that should be noted, and it is transmitted that it is possible to oil quite efficiently from the appearance of the Grease which overflows from the lower end of Wire. Although I am not accustomed to it, I lubricate Clutch Wire and Throttle Wire, and I am satisfied with a new operation feeling that has never existed before.

Probably it is made overseas, but because Instruction Manual of the translation (please input here) is attached by the agency, it was able to use without a problem. There was an impact to dispose of the Wire injector which I had been using immediately. The price is reasonable, but I felt it was reasonable when I saw that Cylinder and Piston are made by SeaRing firmly. I recommend it.

I bought it to try CableLube injection 。
I was wondering if it would be a good idea since it's 3-4 times the price of a regular Cable Louver, but it looks interesting Purchased

It may be a bit of a hassle to set up the installation (injection side & discharge side), but which Cable It's the same with Louver, and I've done it myself, so it should be easy for you guys

I injected the reputedly hard YAMALUBECable lube, which I completed with almost no leaks!
A little leak from the rubber packing at the end of the front side of the photo (anodized thin tube) But it's acceptable 。 An abacus-like rubber that attaches to the Wire's Guide in the Cable LouverV3 There's packing in there, but none of it leaks from there!
I have a feeling that lubricating the Accelerator Wire will be a piece of cake with this! 。

I'll try it soon as it looks like it could be used for bicycles
Cable lube won't go to waste, and if you have one in your family, it may last a lifetime