Kupplungssatz

Комплект дисков сцепления KITACO

Passt:HONDA CHALY 50 FNO, CF50-3000031-, HONDA CRF50F All AE03 models, HONDA CUB press 50 (CDI ignition vehicles)FNO, C50-8500034-0095210 FNO

Pavel Rastrygin

Installiert auf: HONDA Little Cub

Ausgezeichnet

Feb 15, 2023

Комплект дисков сцепления KITACOПродолжаю приводить в порядок свой уставший Honda Little Cub. Работа штатного сцепления несколько жестковата, на webike нашел предложение от KITACO с хорошей ценой. По данному производителю все детали приходят в отличном состоянии и нет проблем при установке. Монтаж еще не производил, но внешне все замечательно!I continue to tidy up my tired Honda Little Cub. The operation of the regular clutch is somewhat harsh, on webike I found an offer from KITACO with a good price. According to this manufacturer, all parts come in excellent condition and there are no problems during installation. Haven't installed it yet, but looks great!

Hilfreich?

I think it's a good product

Passt:HONDA CHALY 50 FNO, CF50-3000031-, HONDA CRF50F All AE03 models, HONDA CUB press 50 (CDI ignition vehicles)FNO, C50-8500034-0095210 FNO

Japanese Webike user

Sehr gut

Nov 5, 2020

Quantity:2pc. This is the second set purchased
The vehicle that was last bored up.
Clutch slips when he kicks
I replaced it because it was there.
This time, the Bore up vehicle is again a Bore up vehicle.
Installed.
I think the product is well made.
It's also excellent in terms of cost.
I have no complaints in terms of performance.

Hilfreich?

It may be because of the Reinforced Clutch, but the ShiftShock is a little large

Passt:HONDA CHALY 50 FNO, CF50-3000031-, HONDA CRF50F All AE03 models, HONDA CUB press 50 (CDI ignition vehicles)FNO, C50-8500034-0095210 FNO

Japan User(translated)

Sehr gut

Apr 20, 2020

[Was there anything that disappointed you?
None in particular

Do you have any wishes or improvements you would like to make for the Manufacturer?
None in particular

[Do you have any products to compare it to?
None

What made you decide to buy?
If you want to change the oil pump to match the Bore up, you can do that too

How was your experience with it?
You need to SHIFT UP at a slow speed because the shock at the time of SHIFT UP is Large The ride is uncomfortable

Was the installation difficult?
With the Special Tool, it's easy

【Please tell me the installation point and hang】
Special Tool is required to replace it, and shifting is not a problem when the Cover is installed Don't forget to Check if you can do it

[Included Parts:were they on?
There is no shortage of what you need

[Others]
Clutch Cover Gasket is required separately

It may be because of the Reinforced Clutch, but th...

Hilfreich?

Passt:HONDA CHALY 50 FNO, CF50-3000031-, HONDA CRF50F All AE03 models, HONDA CUB press 50 (CDI ignition vehicles)FNO, C50-8500034-0095210 FNO

Japan User(translated)

Sehr gut

Jun 10, 2019

Firmly driven

i installed it on my solo Restore It was hard to remove the Gasket I installed it carefully for my car, from Crank to Chain, Tire and Direct The motive force is palpable

Hilfreich?

Exchange with 80cc Bore up!

Passt:HONDA CHALY 50 FNO, CF50-3000031-, HONDA CRF50F All AE03 models, HONDA CUB press 50 (CDI ignition vehicles)FNO, C50-8500034-0095210 FNO

Japan User(translated)

Ausgezeichnet

Aug 14, 2017

While traveling with 80cc Bore up, there was no problem but since slip occurred at KICK, belly was replaced by bad startability.

Although I was worried about Mr. Takekawa made good reputation with With Gasket, Mr. Clutch of Mukawa is commercially available centrifugal Clutch It is not exaggeration to say that it is the most powerful Speculation, but 80 cc Light tune CUB is handled a little by Overspecifications I felt so, so I chose KITACO.

I trusted that my CUB is almost organized by KITACO Parts.

After wearing as expected the slide at the time of KICK has been resolved, KICK feels heavier than before but it is one shot starting!
Behavior at the time of driving but at the first gear at the first gear suddenly Axel when fully open the rotation of Engine can not catch up and it gets caught, if you care about Accelerator operation there is no problem at all.

I also saw posts that Shift change gets stiff but I did not care.

Is it possible to install a person without knowledge just by looking at the Instruction Manual ???.
Well, if you are accustomed to Custom to some extent I think that there is no problem.
I think that it is easier to prepare an electric Impact Driver!