Lenkkegellager

Passt:HONDA BROS650 J , HONDA BROS650 K , HONDA BROS650 L 88-90, HONDA CB-1 89-91, HONDA CB1000 F 95

Although I haven't run for a long distance after wearing, I know the difference from the genuine. It seems to be firm.

Sehr gut

Apr 9, 2012

Hilfreich?

Passt:HONDA BROS650 J , HONDA BROS650 K , HONDA BROS650 L 88-90, HONDA CB-1 89-91, HONDA CB1000 F 95

It is used for [Webike-monitor] NSR250R and 88 models.
Unlike a former ball bearing, it moves smoothly.
I think that it is large well that the former state was too severe.
Durability is likely to be expectable.
Since the price regarded a fe

Sehr gut

Mar 5, 2012

Hilfreich?

Passt:HONDA BROS650 J , HONDA BROS650 K , HONDA BROS650 L 88-90, HONDA CB-1 89-91, HONDA CB1000 F 95

Ausgezeichnet

Jun 27, 2011

It is used by the hornet 250.
When changing a set of the circumferences of a front into VTR1000F, it was recommended to favorite Schopp and equipped, but I think that it is goods of a wonderful about that pure adoption is not carried out.
Although run about 15,000 km from wearing, still touch of connection etc. does not have no maintenance, either, aggressiveness influence can perform it without pain, and a handle also moves to right and left at a smooth.
Although a value is somewhat stretched rather than a pure stainless bearing, if there is an opportunity to exchange, wearing will be recommended quite strongly.

Hilfreich?

Passt:YAMAHA DT125 A-H 74-81, YAMAHA DT125 LC 82, YAMAHA DT175 A-C 74-76, YAMAHA DT175 F-H 79-81, YAMAHA DT250 B-F 75-79

Japanese Webike user

Ausgezeichnet

Aug 4, 2021

Used by MAJESTY125

A lot of Yamaha bikes are ball type, which is fine from a handling point of view, but the MAJESTY125 has a lot of Stem gurgling problems!
So, I replaced it with this product of high durability.
Of course, the new one works great and is now normal from the dizzy Handling that seemed to mock up.

However, the replacement work is very Large strange, Top level so far (Large strange in a sense than full Overhaul by taking down the Engine)
It's not the kind of difficulty that can be managed with tools, and beating the Race is a feat of strength.
Of course, after all the rods around the front, we had to fight with the bearings for a few hours, and the race press fitment was also very careful.
If you don't know what you're doing, it's best to take it to a shop, because you won't be able to return it to its original state and take it to a motorcycle shop.

Hilfreich?

Passt:SUZUKI RM125 79-80, SUZUKI RM200 79-80, SUZUKI RM400 79-80, YAMAHA FJ600 H-K 84-85, YAMAHA FZ250 FAZER

I'll believe in "Made in Japan quality"!

Durchschnittlich

May 13, 2020

Frame headPipe Outer for under bracket bearing on the underside The process of typing lace was a battle with anxiety … Han Merlingu typing in is noisy (Neighborhood nuisance.) I was so scared because the position where the outer lace stops is so far back Is there any mistake in the parts? Is it possible that the handlebar is not turned off due to contact with the pipe?
The inner diameter of the outer lace is thinner than the diameter of the inner wall of the head pipe, so remove it again There are no dents in the bearing Also, when the bearing is worn out, the bearing's wall thickness is not in contact with the bearing's thickness, making it inoperable hellip; I was so worried
On the way, I tried to apply the Under bracket; Because it was not possible to turn back, I continued typing as it was
…As a result, the installation is complete I did We'll run for a while and see what happens It was a windy day, but the neck root (Stem) The feeling of rigidity transmitted from the car is increased and the car becomes stable and fun to drive
I think you should ask Shop to do the work for you